Hindustan Aeronautics Limited(HAL) sample questions books for Computer Science, Electrical, Electronics, Civil, Mechanical, Metallurgy, Production, Aeronautics Stream
HAL Recruitment Exam details
Hindustan Aeronautics Limited(HAL) is going to conduct the Online examination for the various Management Trainee post. HAL is going to conduct the Online selection test at various centers across India from 13th November 2013 to 22nd November 2013. The details of the examination with sample questions is given below. This page will be updated with more & more questions to help the candidates to prepare for the examination moreover we have also provided some links of the good book, you can also refer them.
The candidates will be selected for Interview based on the result of the Online Selection Test marks. However it depends on the marks but they will select 1 out of every 5 candidate who are giving exam for the particular post. HAL is also giving second chance to all the reserved category candidates by regrouping them & then selecting them for the interview in 1:5 ratio. The final selection will be done by assigning
the weight age of 85% marks for Online Test and 15% marks for Interview.
Exam Centers
The Online Test will be held at Ahmedabad, Allahabad, Bangalore, Bhopal, Bhubaneswar, Chandigarh, Chennai, Coimbatore, Dehradun, Delhi, Ernakulam, Gulbarga, Gurgaon, Guwahati, Hyderabad, Jaipur, Kanpur, Kolkata, Kota, Lucknow, Madurai, Mumbai, Nagpur, Nashik, Noida, Pune, Ranchi, Trivandrum, Vijayawada & Visakhapatnam.
Exam Schema
Test Language: Hindi or English
Total No. of Question: 160
Total Time Allotted: Two and Half hours
Multiple Choice Questions (MCQs)
1) Part – I will consist of 20 MCQs on General Awareness.
2) Part – II will consist of 40 MCQs on English & Reasoning.
3) Part – III will consist of 100 MCQs on the concerned discipline of Engineering / Marketing / HR / Legal. For Management Trainees (Marketing),
Part – III will consist of
50 questions from the respective Engineering discipline
50 questions from Marketing discipline.
Selection wise Sample Questions
Part-I: General Awareness
This section will contain 20 MCQ which will check your General Knowledge including knowledge of Current Affairs. However there is no limit to prepare for this section so we recommend you to do other part first as they contain more weightage with more number of questions. However we have provided few current affairs topic
Part-II: English & Reasoning
This section will contain 40 MCQ which will test English & Reasoning Skills. Few sample questions are given below
Ques: The novel comes as a ______ to all women dumped by ______ males who will feel provoked at the title of the book, or at the sight of the picture on the cover.
1. surprise .... electric
2. solace.....narcissistic
3. comfort.....non-conformist
4. prelude...chauvinistic
Ans is 2
Five houses ran in a race
1) There were noties
2. Sikander did not come first
3) Star was neither first nor last
4) Mugal Glory came in one place after sikander
5) Zozo was not second
6) Rangali was two place below Zozo
Who finished first ?
a) Star b) Zozo c) Ranglia, d) Mugal Glory
Who was last in the race ?
a) Ranglia, b) Mugal Glory c) Star d) Zozo
Recommended Books
Part-III: Questions from Engineering Discipline + Marketing
Hindustan Aeronautics Limited(HAL) is going to conduct the Online examination for the various Management Trainee post. HAL is going to conduct the Online selection test at various centers across India from 13th November 2013 to 22nd November 2013. The details of the examination with sample questions is given below. This page will be updated with more & more questions to help the candidates to prepare for the examination moreover we have also provided some links of the good book, you can also refer them.
The candidates will be selected for Interview based on the result of the Online Selection Test marks. However it depends on the marks but they will select 1 out of every 5 candidate who are giving exam for the particular post. HAL is also giving second chance to all the reserved category candidates by regrouping them & then selecting them for the interview in 1:5 ratio. The final selection will be done by assigning
the weight age of 85% marks for Online Test and 15% marks for Interview.
Exam Centers
The Online Test will be held at Ahmedabad, Allahabad, Bangalore, Bhopal, Bhubaneswar, Chandigarh, Chennai, Coimbatore, Dehradun, Delhi, Ernakulam, Gulbarga, Gurgaon, Guwahati, Hyderabad, Jaipur, Kanpur, Kolkata, Kota, Lucknow, Madurai, Mumbai, Nagpur, Nashik, Noida, Pune, Ranchi, Trivandrum, Vijayawada & Visakhapatnam.
Exam Schema
Test Language: Hindi or English
Total No. of Question: 160
Total Time Allotted: Two and Half hours
Multiple Choice Questions (MCQs)
1) Part – I will consist of 20 MCQs on General Awareness.
2) Part – II will consist of 40 MCQs on English & Reasoning.
3) Part – III will consist of 100 MCQs on the concerned discipline of Engineering / Marketing / HR / Legal. For Management Trainees (Marketing),
Part – III will consist of
50 questions from the respective Engineering discipline
50 questions from Marketing discipline.
Selection wise Sample Questions
Part-I: General Awareness
This section will contain 20 MCQ which will check your General Knowledge including knowledge of Current Affairs. However there is no limit to prepare for this section so we recommend you to do other part first as they contain more weightage with more number of questions. However we have provided few current affairs topic
- Bharti Walmart Discussion
- Coal scam singes Birla, PMO
- US government shutdown ends as Republicans blink
- Cyclone Phailin hits Odisha, AP
- ASI gold hunt over in U.P. village nothing found after hours of search.
- World Bank praises MNREGA job scheme
- EC disallows launch of LPG scheme in poll-bound states
- Rail wheel manufacturing unit inaugurated in Rae Bareli
- Reserve 3% govt. jobs for disabled–SC
- India to have separate ASEAN Mission
- India signs MoUs with 7 countries for Nalanda University
- India 63rd on 2013 Global Hunger Index
- US Ship with unauthorised weapons detained off TN coast
- India, Nepal organised exercise ‘Surya Kiran’
- President pays tribute to Indian martyrs of WW I:
- 129th Inter-Parliamentary Union (IPU) meeting organised
- India to be world’s most populous nation by 2050– Study
- Former Union Minister Mohan Dharia passes away
- Parliament passes land acquisition bill
- Street Vendors Bill passed
- Globemaster III inducted into the IAF
- GSAT-7 launched successfully
- Parliament passes Manual Scavengers Bill
- Implementation of Rajiv Awas Yojana approved
- Parliament passes Food Security Bill
- Government to set up Judicial Appointments Commission
- Ahimsa Messenger’ programme launched
- Rajiv Gandhi Wildlife Conservation Award conferred
- Govt denies category status for Jharkhand, Odisha & Rajasthan
- National Media Centre inaugurated in New Delhi
- MoEF approves policy to prohibit removal of shark fins
- Bengal launches its ‘safe’ savings scheme
- ‘Encyclopedia of Hinduism’ launched
- Deepak Sandhu is first female Chief Information Commissioner
- India, Iraq sign pact to strengthen cooperation in energy sector
Recommended Books
This section will contain 40 MCQ which will test English & Reasoning Skills. Few sample questions are given below
Ques: The novel comes as a ______ to all women dumped by ______ males who will feel provoked at the title of the book, or at the sight of the picture on the cover.
1. surprise .... electric
2. solace.....narcissistic
3. comfort.....non-conformist
4. prelude...chauvinistic
Ans is 2
Five houses ran in a race
1) There were noties
2. Sikander did not come first
3) Star was neither first nor last
4) Mugal Glory came in one place after sikander
5) Zozo was not second
6) Rangali was two place below Zozo
Who finished first ?
a) Star b) Zozo c) Ranglia, d) Mugal Glory
Who was last in the race ?
a) Ranglia, b) Mugal Glory c) Star d) Zozo
Recommended Books
Part-III: Questions from Engineering Discipline + Marketing
This section will contain questions from your discipline
Computer Science Stream
Here is the list of Few topics which you can study before appearing in the exam
Database Management System(Deadlock management, Firing query, )
Digital Logical Design(Different Types of gates AND, OR, NAND, OR & their operations, Type conversion from decimal to binary, hexadecimal etc)
Data File Structure(Stack, Queue, Link list, Tree, Graph & their working)
Operating System (Thread operation, Memory Management, Deadlock problem, security)
Languages- C/C++, Java, Pl/SQl, .NET
Computer Networks(Different Types of Layers & their working)
E-commerce & E-business (Business Model, Advertising models, SCM, CRM, ERP)
Computer Graphics
Information Security(Authentication, Confidentiality, Integrity etc)
Sample Questions
Ques: Which of these is not a browser ?
a) Firefox b) Chrome, c) IE d) Photoshop
Ques: 1 MB is equal to how many bytes ?
a) 1,048,576 b) 1,000,000 c) 10,400,000 d) 1,100,000
Solution:
1024 bytes = 1 Kilobyte. 1024 Kilobytes = 1 Megabyte. Therefore;. 1024 * 1024 = 1,048,576
Ques: Which of the following special symbol allowed in a variable name?
A.* (asterisk)
B.| (pipeline)
C.- (hyphen)
D._ (underscore)
Answer: Option D
Ques: The following are components of a database except ________ .?
A. user data
B. metadata
C. reports
D. indexes
Ans is C. reports
Ques: No.of 2-input multiplexers needed to construct a 210 input multiplexer….
a) 12
b) 31
c) 20
d)16
Ques: Which of the following is not a primitive type in C
a) Int
b) Float
c) Char
d) none of these
Ques: Register variables are stored in ---
a) CPU
b) main memory
c) secondary memory
d) peripheral memory
Recommended Books
Sample Questions for Electrical & Electronics Stream
Ques: The formula to find I when the values of V and R are known is
A. I = VR
B. I = R/V
C. V = IR
D. I = V/R
Ques: Resistance is measured in
A. henries B. ohms
C. hertz D. watts
Ques: How much voltage is needed to produce 2.5 A of current through a 200 resistor?
A. 50 V
B. 500 V
C. 80 V
D. 8 V
Ques: Fourteen milliamperes can be expressed as
A. 14 MA
B. 14 µA
C. 14 kA
D. 14 mA
Ques: When an additional resistor is connected across an existing parallel circuit, the total resistance
A. remains the same
B. decreases by the value of the added resistor
C. increases by the value of the added resistor
D. decreases
Ques: Voltage is measured in
A. volts
B. farads
C. watts
D. ohms
Ques: Current is measured in
A. watts
B. volts
C. henries
D. amperes
Ques: How much continuous current can be drawn from a 60 Ah battery for 14 h?
A. 42.8 A
B. 428 A
C. 4.28 A
D. 4.2 A
Ques: The Thevenin equivalent voltage is
A. equal to the source voltage
B. the same as the load voltage
C. the open circuit voltage
D. none of the above
Ques: How many degrees are there in /3 rad?
A. 6°
B. 60°
C. 180°
D. 27°
Ques: A pulse waveform has a high time of 8 ms and a pulse width of 32 ms. The duty cycle is
A. 25%
B. 50%
C. 1%
D. 100%
Recommended Books
Sample Questions for Mechanical Stream
Ques: If the resultant of two equal forces has the same magnitude as either of the forces, then the angle between the two forces is
A. 30°
B. 60°
C. 90°
D. 120°
Ques: The efficiency and work ratio of a simple gas turbine cycle are
A. low
B. very low
C. high
D. very high
Ques: The unit of angular acceleration is
A. N-m
B. m/s
C. m/s2
D.rad/s2
Ques: Which of the following is the lightest and most volatile liquid fuel?
A. Gasoline
B. Kerosene
C. Fuel oil
D. Nitrogen
Ques: The specific heat of water is
A. 1.817
B. 2512
C. 4.187
D. none of these
Ques: The sleeve or muff coupling is designed as a
A. dun cylinder
B. thick cylinder
C. solid shaft
D. hollow shaft
Ques: The number of slots in a 25 mm castle nut is
A. 2
B. 4
C. 6
D. 8
Ques: A transmission shaft includes
A. counter shaft
B. line shaft
C. over head shaft
D. all of these
Ques: Euler's formula holds good only for
A. short columns
B. long columns
C. both short and long columns
D. weak columns
Ques: When shear force at a point is zero, then bending moment is __________ at that point.
A. zero
B. minimum
C. maximum
D. infinity
Ques: The coefficient of restitution for elastic bodies is one.
A. Correct
B. Incorrect
C. Can't say
Recommended Books
Sample Questions for Aeronautics Stream
Air Fuel ratio in a jet engine will be of the order of:
(a) 10:1 (b) 15:1
(c) 20:1 (d) 60:1
Fire tube boilers are limited to a maximum design working pressure of :
(a) 1 kg/cm2 (b) 6 kg/cm2
(C) 17 kg/cm2 (d ) 100 kg/cm2
An aircraft in trimmed condition has zero pitching moment at
(A) its aerodynamic centre. (B) its centre of gravity.
(C) 25% of its mean aerodynamic chord. (D) 50% of its wing root chord.
In an aircraft, elevator control effectiveness determines
(A) turn radius.
(B) rate of climb.
(C) forward-most location of the centre of gravity.
(D) aft-most location of the centre of gravity.
The ideal static pressure coefficient of a diffuser with an area ratio of 2.0 is
(A) 0.25 (B) 0.50 (C) 0.75 (D) 1.0
Recommended Books
Production Stream
Few topics you need to cover are given below
Dynamic Force analysis of mechanisms:
Introduction, D’alembert’s principle, equivalent offset inertia force, dynamic analysis of four link mechanism, dynamic analysis of slider crank mechanism, velocity & acceleration of piston, angular velocity & angular acceleration of connecting rod, engine force analysis, turning moment on crank shaft, dynamically equivalent system inertia of the connecting rod, inertia force in reciprocating engines, turning moment diagrams, fluctuation of energy, fly wheel.
Balancing:
Introduction, static balancing, dynamic balancing, transference of force from one plane to another plane, balancing of several masses in different planes, force balancing of linkages, balancing of reciprocating mass, balancing of locomotives , secondary balancing, balancing of inline engines, balancing of v-engines
Vibrations:
Introduction, definition, types of vibrations, basic features of vibrating system, degree of freedom. Longitudinal vibration:- free long vibration, displacement, velocity & acceleration. Inertia
Engineering symbols(drafting):
Geometric symbols, surface roughness symbols, welding symbols, Limits and fits
Fasteners:
Introduction, types, screw thread terminology, forms of screw thread, types of nuts, locking arrangements of nuts, set screws, stud/stud bolt, foundation bolts, keys, cotter joint, rivet heads, welded joints,
Metallurgy Stream
Metal Forming Processes
Rolling, Forging, Extrusion, Fracture, Creep & Fatigue
Introduction to Metal Forming:
Metallurgical aspects of metal forming, slip, twinning mechanics of plastic deformation, effects of temperature, strain rate, micro structure and friction in metal forming-yield criteria and their significance, Classification of Metal Forming Processes, Advantages and Limitations, Stress strain relations in elastic and plastic deformation, concept of flow stresses, deformation mechanisms, Hot and Cold Working Processes and It’s Effect on Mechanical Properties
Iron Making
Non - Ferrous Extractive Metallurgy
Foundry Technology
Fuels, Furnaces and Refractory
Powder Metullurgy
Alloy Design
Non Destructive Testing
Metell Joining Process
Eletrometallurgy
Recommended Books
Computer Science Stream
Here is the list of Few topics which you can study before appearing in the exam
Database Management System(Deadlock management, Firing query, )
Digital Logical Design(Different Types of gates AND, OR, NAND, OR & their operations, Type conversion from decimal to binary, hexadecimal etc)
Data File Structure(Stack, Queue, Link list, Tree, Graph & their working)
Operating System (Thread operation, Memory Management, Deadlock problem, security)
Languages- C/C++, Java, Pl/SQl, .NET
Computer Networks(Different Types of Layers & their working)
E-commerce & E-business (Business Model, Advertising models, SCM, CRM, ERP)
Computer Graphics
Information Security(Authentication, Confidentiality, Integrity etc)
Sample Questions
Ques: Which of these is not a browser ?
a) Firefox b) Chrome, c) IE d) Photoshop
Ques: 1 MB is equal to how many bytes ?
a) 1,048,576 b) 1,000,000 c) 10,400,000 d) 1,100,000
Solution:
1024 bytes = 1 Kilobyte. 1024 Kilobytes = 1 Megabyte. Therefore;. 1024 * 1024 = 1,048,576
Ques: Which of the following special symbol allowed in a variable name?
A.* (asterisk)
B.| (pipeline)
C.- (hyphen)
D._ (underscore)
Answer: Option D
Ques: The following are components of a database except ________ .?
A. user data
B. metadata
C. reports
D. indexes
Ans is C. reports
Ques: No.of 2-input multiplexers needed to construct a 210 input multiplexer….
a) 12
b) 31
c) 20
d)16
Ques: Which of the following is not a primitive type in C
a) Int
b) Float
c) Char
d) none of these
Ques: Register variables are stored in ---
a) CPU
b) main memory
c) secondary memory
d) peripheral memory
Recommended Books
Sample Questions for Electrical & Electronics Stream
Ques: The formula to find I when the values of V and R are known is
A. I = VR
B. I = R/V
C. V = IR
D. I = V/R
Ques: Resistance is measured in
A. henries B. ohms
C. hertz D. watts
Ques: How much voltage is needed to produce 2.5 A of current through a 200 resistor?
A. 50 V
B. 500 V
C. 80 V
D. 8 V
Ques: Fourteen milliamperes can be expressed as
A. 14 MA
B. 14 µA
C. 14 kA
D. 14 mA
Ques: When an additional resistor is connected across an existing parallel circuit, the total resistance
A. remains the same
B. decreases by the value of the added resistor
C. increases by the value of the added resistor
D. decreases
Ques: Voltage is measured in
A. volts
B. farads
C. watts
D. ohms
Ques: Current is measured in
A. watts
B. volts
C. henries
D. amperes
Ques: How much continuous current can be drawn from a 60 Ah battery for 14 h?
A. 42.8 A
B. 428 A
C. 4.28 A
D. 4.2 A
Ques: The Thevenin equivalent voltage is
A. equal to the source voltage
B. the same as the load voltage
C. the open circuit voltage
D. none of the above
Ques: How many degrees are there in /3 rad?
A. 6°
B. 60°
C. 180°
D. 27°
Ques: A pulse waveform has a high time of 8 ms and a pulse width of 32 ms. The duty cycle is
A. 25%
B. 50%
C. 1%
D. 100%
Recommended Books
Sample Questions for Mechanical Stream
Ques: If the resultant of two equal forces has the same magnitude as either of the forces, then the angle between the two forces is
A. 30°
B. 60°
C. 90°
D. 120°
Ques: The efficiency and work ratio of a simple gas turbine cycle are
A. low
B. very low
C. high
D. very high
Ques: The unit of angular acceleration is
A. N-m
B. m/s
C. m/s2
D.rad/s2
Ques: Which of the following is the lightest and most volatile liquid fuel?
A. Gasoline
B. Kerosene
C. Fuel oil
D. Nitrogen
Ques: The specific heat of water is
A. 1.817
B. 2512
C. 4.187
D. none of these
Ques: The sleeve or muff coupling is designed as a
A. dun cylinder
B. thick cylinder
C. solid shaft
D. hollow shaft
Ques: The number of slots in a 25 mm castle nut is
A. 2
B. 4
C. 6
D. 8
Ques: A transmission shaft includes
A. counter shaft
B. line shaft
C. over head shaft
D. all of these
Ques: Euler's formula holds good only for
A. short columns
B. long columns
C. both short and long columns
D. weak columns
Ques: When shear force at a point is zero, then bending moment is __________ at that point.
A. zero
B. minimum
C. maximum
D. infinity
Ques: The coefficient of restitution for elastic bodies is one.
A. Correct
B. Incorrect
C. Can't say
Recommended Books
Sample Questions for Aeronautics Stream
Air Fuel ratio in a jet engine will be of the order of:
(a) 10:1 (b) 15:1
(c) 20:1 (d) 60:1
Fire tube boilers are limited to a maximum design working pressure of :
(a) 1 kg/cm2 (b) 6 kg/cm2
(C) 17 kg/cm2 (d ) 100 kg/cm2
An aircraft in trimmed condition has zero pitching moment at
(A) its aerodynamic centre. (B) its centre of gravity.
(C) 25% of its mean aerodynamic chord. (D) 50% of its wing root chord.
In an aircraft, elevator control effectiveness determines
(A) turn radius.
(B) rate of climb.
(C) forward-most location of the centre of gravity.
(D) aft-most location of the centre of gravity.
The ideal static pressure coefficient of a diffuser with an area ratio of 2.0 is
(A) 0.25 (B) 0.50 (C) 0.75 (D) 1.0
Recommended Books
Production Stream
Few topics you need to cover are given below
Dynamic Force analysis of mechanisms:
Introduction, D’alembert’s principle, equivalent offset inertia force, dynamic analysis of four link mechanism, dynamic analysis of slider crank mechanism, velocity & acceleration of piston, angular velocity & angular acceleration of connecting rod, engine force analysis, turning moment on crank shaft, dynamically equivalent system inertia of the connecting rod, inertia force in reciprocating engines, turning moment diagrams, fluctuation of energy, fly wheel.
Balancing:
Introduction, static balancing, dynamic balancing, transference of force from one plane to another plane, balancing of several masses in different planes, force balancing of linkages, balancing of reciprocating mass, balancing of locomotives , secondary balancing, balancing of inline engines, balancing of v-engines
Vibrations:
Introduction, definition, types of vibrations, basic features of vibrating system, degree of freedom. Longitudinal vibration:- free long vibration, displacement, velocity & acceleration. Inertia
Engineering symbols(drafting):
Geometric symbols, surface roughness symbols, welding symbols, Limits and fits
Fasteners:
Introduction, types, screw thread terminology, forms of screw thread, types of nuts, locking arrangements of nuts, set screws, stud/stud bolt, foundation bolts, keys, cotter joint, rivet heads, welded joints,
Productivity Improvement Methods
Performance Rating, Wage Payment & Incentive Plans, Various incentive schemes, Performance Rating
Productivity Management
Definition, Concept and Importance of productivity, Difference between Production and Productivity, Tools of productivity, Reasons for low productivity, Factors that help increasing productivity, Productivity index, Kinds of productivity measurement, Causes of low productivity and techniques of their elimination, Factors affecting productivity, Technical methods to improve productivity, Main contributors to productivity improvement, Advantages from increased productivity.
Metal Forming Processes
Rolling, Forging, Extrusion, Fracture, Creep & Fatigue
Introduction to Metal Forming:
Metallurgical aspects of metal forming, slip, twinning mechanics of plastic deformation, effects of temperature, strain rate, micro structure and friction in metal forming-yield criteria and their significance, Classification of Metal Forming Processes, Advantages and Limitations, Stress strain relations in elastic and plastic deformation, concept of flow stresses, deformation mechanisms, Hot and Cold Working Processes and It’s Effect on Mechanical Properties
Iron Making
Non - Ferrous Extractive Metallurgy
Foundry Technology
Fuels, Furnaces and Refractory
Powder Metullurgy
Alloy Design
Non Destructive Testing
Metell Joining Process
Eletrometallurgy
Recommended Books
Engineer Vacancies
| ||
| Mechanical Engineer | Civil Engineer | Diploma Engineer |
| Electrical Engineer | Computer Engineer | B.E / B.Tech |
Latest Vacancies
| ||
| SSC/UPSC Job | Walk-in Interview | Defence Jobs |
| Government Job | Railway Jobs | Teacher / Professor |
No comments:
Post a Comment